Collection by Series

This category contains different series, editions or “product line” collections put into one category per series, so that it’s easier for users to find other projects and products from the same series.

Showing all 10 results

  • Ceramic Frequency Screwdrivers Mount (8pcs)

    Just a simple desk/workbench/wall mount for the cheap Chinese (Yueran) Ceramic Frequency Screwdrivers. These are often sold as a set of 8, and are also sold under many different ‘brand names’

    Download: 282kb

  • Component Organizer Divider

    Just a simple printable divider for component storage cabinets, often also called: parts organizers, parts cabinets or in Dutch: assortimentskast & ladekast

    Size of my dividers: 51.50x30x2mm

    NOTE: I don’t remember the exact brand of my cabinet, so make sure to check the dimensions of your own dividers before printing these to ensure that these will fit your cabinet.

    Model: XNL-WST15722
    Download: 100kb

  • Desk Outlet Socket Protection

    Just a very simple (but effective) solution to close-off horizontally installed desk outlets .

    I designed this (simple) solution to protect our pet (rescue) pigeon Sophie against accidentally putting her feet into the desk sockets (which where obviously already installed there before we got her ;) )

    This is a simple 3D print of two parts (the closing cap and the ‘key’), both the key and the cap(s) take a 10x3mm neodymium magnet.

    Download: 85kb

  • Hakko Soldering Tip Storage (wall/desk mount)

    A simple and elegant way to store up to 5 soldering tips for your Hakko® soldering iron.

    This design is intended to be installed onto a wooden plate/wall of your workshop or desk.

    When printed in two colors (switching filament mid-print) you can even make it match your Hakko® soldering Iron perfectly when using blue and yellow as filament colors.

    Download: 40KB

  • PCB Holder Workbench Mount (upside down mount!)

    Just a simple desk/workbench/wall mount for my (cheap) PCB Holder so it always have it within reach when I need it (see example photos).

    Download: 29kb

  • Vetus® Tweezers Workbench Mount (6pcs)

    Just a simple desk/workbench/wall mount for six Vetus® Tweezers (imitation tweezers also fit in this mount).

  • Wall Storage Mounts (Round 3 Sizes)

    Just a simple wall mounted solution to store things like cabledutcs, screw-threads, metal rods and stuff like that in three different sizes:

    40mm     (XLT240624-40)
    50mm (XLT240624-50)
    60mm (XLT240624-60)

    (All sizes included in one download)

    Download: 1MB

  • XNL F.U.T.S. – Full USB to TTL Serial Adapter

    The XNL F.U.T.S. is ‘our answer’ to a problem we personally had quite a few times: Finding a decent USB to Serial/UART board which either just works, and/or had more than just the RX, TX and RTS available.

    The XNL F.U.T.S. stands for Full USB to TTL Serial Adapter, and it basically is a serial adapter/board which gives you a full USB serial port including ALL serial pins including: RX, TX, RTS, CTS, DTR, DSR, DCD, and RI (and of course VCC and ground).

    The XNL F.U.T.S. uses the CH340G IC, of which the drivers can be downloaded here.

    Download Size: 1.2MB

  • XNL LABUNO Overkill Edition

    The XNL LABUNO Overkill Edition is an ‘expanded version’ of our XNL LABUNO USB.

    Some of the features you have full control over with the LABUNO are:
    – Pull-up resistors on the ‘reset-line’
    – Enable/Disable RTS Reset
    – Switch TTL communication between HW / SW
    – VCC source selection
    – High power LM3940 3.3V Regulator
    – Full control over the serial pins
    – Build-in support for ESP board (and communication)

    Additional Features with the LABUNO Overkill Edition:
    – Full access to ALL serial/UART pins
    – Three onboard Ready to use Servo Ports
    – I2C/OLED LCD Header Ready to use
    – Onboard AVR/ISP Programmer using the
    Arduino as ISP sketch.

    Next to these (and more) features, the headers (next to the microcontroller) also ‘line-up’ 1:1 with the microcontroller pin-out.

    NOTE:
    This has it’s own ‘onboard’ USB to serial (TTL) chip (the CH340G), while the LABUNO does not have any USB controller/chip onboard. So if you prefer to choose your own USB->Serial chip, we would like you to recommend to check out the LABUNO instead. We also have the XNL LABUNO USB which is a bit more ‘subtle’ so to speak.

    “Multi Pack” NOTE:
    The (NON USB) XNL LABUNO download also contains a panelized version of the XNL LABUNO which includes two XNL Logic Monitors, an XNL ESP Direct Board, and an XNL WESP Board which means that it might actually be cheaper to order the panelized version (if your PCB Manufacturer allows pre-panelized boards) if you need or want all modules.

    Download Size: 4.5mb

  • XNL Microscope Adapter (for Microphone Arm)

    I love my cheap Chinese AliExpress (Electronics) microscope, but it just drove me absolutely bonkers when I tried to use it with larger boards.

    So I decided to design as small (3D Printed) adapter which uses a 3/8″ thread, so that the cheap Microscope could be placed on a microphone arm, basically giving it the same flexibility as the (much) more expensive electronics lab microscopes but for a much lower price (for me totaling around €65,-)

    I made a YouTube video about this project here

    Download: 2.1mb
    P/N: XLT290724