-
This mini “board” is officially part of the XNL LABUNO Panelized version (which is included in the XNL LABUNO Download), and it is only provided as separate ‘project’/download for reference.
You do not need this board!
Literally! You DO NOT need this board ;) you can achieve EXACTLY the same with two (female-female) jumper wires! Please read the additional information section for more information.
“Multi Pack” NOTE:
The (NON USB) XNL LABUNO download also contains a panelized version of the XNL LABUNO which includes two XNL Logic Monitors, an XNL ESP Direct Board, and an XNL WESP Board which means that it might actually be cheaper to order the panelized version (if your PCB Manufacturer allows pre-panelized boards) if you need or want all modules.
Download Size: 440kb
-
EoL
This small board is what I/we’ve used for a long time when we needed to boot-load our newly arrived Atmega328’s, often we used this board together with the XNL ISP Speed Flash Board to flash and/or boot-load all kinds of different AVR’s for our projects.
These days we however don’t use (or support) it anymore, simply because the XNL LABUNO Overkill Edition has an ISP Programmer build-in, which also has it’s own onboard USB controller, which means we don’t have to connect it to an USB to Serial adapter first (like the XNL F.U.T.S.).
NOTE: The larger (red) board shown in the photo’s is the XNL ISP Speed Flash Board which is not included in this download!
Download Size: 1.75mb
-
The XNL Breadboard I/O is an solution to always have your breadboard ready-to-go by just having to plugin one USB cable to get up-and-running with your project(s). This also makes it super easy to quickly switch between projects/breadboards or to resume the next day with your project without having to ‘re-setup’ the power from your lab power supply, the jumper wires for your power strips etc etc.
TIP: In a YouTube video here I also show how to build the large XXL breadboard shown in the photos.
Some of the features of an Breadboard with the XNL Breadboard I/O:
– It’s very easy and fast to get to work by just plugging-in one USB cable.
– Two onboard voltage and current displays (one for the USB and one for the DC Jack)
– A stable onboard 3.3V regulator (LM3940)
– Easy to turn power rails on and off (if using the DIP Switches)
– Onboard 500mA over-current/short-circuit protection (which can be bypassed)
– 2 USB Breakouts (1X USB A, 1X USB B)
– DC Jack input for other voltages like 12V, 24V etc.
“Multi Pack” NOTE:
This download also contains the following 3D Printable parts: The enclosures for the displays, a drill stencil for the display enclosure, A closed bottom for the display enclosure, the XNL Breadboard I/O PCB Baseplate and a 40degree angled mount for an additional breadboard strip on the top of your breadboard (see photo’s for the purpose of this)
Download Size: 5mb
-
This small little board, makes it ‘just that little bit’ easier, faster and cleaner to setup a ‘bare-minimum’ configuration on your breadboard for the ATmega1284 Microcontroller.
NOTES
– This board can also be used for other microcontrollers like the ATmega644.
– Best and most effective when used in combination with the XNL Easy Breadboard Crystal
Download Size: 817kb
-
This small little board, makes it ‘just that little bit’ easier, faster and cleaner to setup a ‘bare-minimum’ configuration on your breadboard for the ATmega328 Microcontroller.
NOTES
– This board can also be used for other microcontrollers like the ATmega168, ATmega48, ATmega88
– Best and most effective when used in combination with the XNL Easy Breadboard Crystal
Download Size: 817kb
-
This small little board, makes it ‘just that little bit’ easier, faster and cleaner to setup a ‘bare-minimum’ configuration several different ATmega microcontrollers.
– This board can be used with microcontrollers like the ATmega328, ATmega168, ATmega48, ATmega88, ATmega1284, ATmega644 and possibly many others.
– Best and most effective when used in combination with a XNL LessMess328 or XNL LessMess1284
Download Size: 913kb
-
A simple add-on for the XNL LABUNO Overkill Edition which enables you to quickly and easily flash and/or boot-load a wide range of AVR microcontrollers by simply using your XNL LABUNO Overkill Edition’s AVR/ISP Programmer header
Microcontrollers supported by this board
– ATmega 48, 88, 168 & 328 (28 pin)
– ATmega 644 & 1284 (40 Pin)
– Tiny 2313 (20 Pin)
– Tiny 44 & 84 (14 pin)
– Tiny 45 & 85 (8 pin)
Download Size: 1.6mb
-
The XNL LABUNO is ‘our answer’ to the Arduino® Uno, but with (much) more control over your hardware.
Some of the features you have full control over with the LABUNO are:
– Pull-up resistors on the ‘reset-line’
– Enable/Disable RTS Reset
– Switch TTL communication between HW / SW
– VCC source selection
– High power LM3940 3.3V Regulator
– Full control over the serial pins
– Build-in support for ESP board (and communication)
Next to these (and more) features, the headers (next to the microcontroller) also ‘line-up’ 1:1 with the microcontroller pin-out.
NOTE:
This model requires an USB->TTL adapter like for example the XNL F.U.T.S. or an FTDI cable to communicate with your computer. The LABUNO USB has an onboard USB-Serial chip and thus does not need an additional USB adapter/cable. We also have the LABUNO Overkill Edition which has even more ‘on-board’ features and also has an onboard USB controller.
“Multi Pack” NOTE:
This download also contains a panelized version of the XNL LABUNO which includes two XNL Logic Monitors, an XNL ESP Direct Board, and an XNL WESP Board which means that it might actually be cheaper to order the panelized version (if your PCB Manufacturer allows pre-panelized boards) if you need or want all modules.
Download Size: 4mb
-
The XNL LABUNO Overkill Edition is an ‘expanded version’ of our XNL LABUNO USB.
Some of the features you have full control over with the LABUNO are:
– Pull-up resistors on the ‘reset-line’
– Enable/Disable RTS Reset
– Switch TTL communication between HW / SW
– VCC source selection
– High power LM3940 3.3V Regulator
– Full control over the serial pins
– Build-in support for ESP board (and communication)
Additional Features with the LABUNO Overkill Edition:
– Full access to ALL serial/UART pins
– Three onboard Ready to use Servo Ports
– I2C/OLED LCD Header Ready to use
– Onboard AVR/ISP Programmer using the
Arduino as ISP sketch.
Next to these (and more) features, the headers (next to the microcontroller) also ‘line-up’ 1:1 with the microcontroller pin-out.
NOTE:
This has it’s own ‘onboard’ USB to serial (TTL) chip (the CH340G), while the LABUNO does not have any USB controller/chip onboard. So if you prefer to choose your own USB->Serial chip, we would like you to recommend to check out the LABUNO instead. We also have the XNL LABUNO USB which is a bit more ‘subtle’ so to speak.
“Multi Pack” NOTE:
The (NON USB) XNL LABUNO download also contains a panelized version of the XNL LABUNO which includes two XNL Logic Monitors, an XNL ESP Direct Board, and an XNL WESP Board which means that it might actually be cheaper to order the panelized version (if your PCB Manufacturer allows pre-panelized boards) if you need or want all modules.
Download Size: 4.5mb
-
The XNL LABUNO USB is ‘our answer’ to the Arduino® Uno, but with (much) more control over your hardware.
Some of the features you have full control over with the LABUNO are:
– Pull-up resistors on the ‘reset-line’
– Enable/Disable RTS Reset
– Switch TTL communication between HW / SW
– VCC source selection
– High power LM3940 3.3V Regulator
– Full control over the serial pins
– Build-in support for ESP board (and communication)
Next to these (and more) features, the headers (next to the microcontroller) also ‘line-up’ 1:1 with the microcontroller pin-out.
NOTE:
This has it’s own ‘onboard’ USB to serial (TTL) chip (the CH340G), while the LABUNO does not have any USB controller/chip onboard. So if you prefer to choose your own USB->Serial chip, we would like you to recommend to check out the LABUNO instead. We also have the LABUNO Overkill Edition which has even more ‘on-board’ features and also has an onboard USB controller.
“Multi Pack” NOTE:
The (NON USB) XNL LABUNO download also contains a panelized version of the XNL LABUNO which includes two XNL Logic Monitors, an XNL ESP Direct Board, and an XNL WESP Board which means that it might actually be cheaper to order the panelized version (if your PCB Manufacturer allows pre-panelized boards) if you need or want all modules.
Download Size: 3.8mb
-
The XNL Logic Monitor is a small ‘add-on’ for the XNL LABUNO and XNL LABUNO USB which can add an RX and TX LED for the UART (Serial) ports of the LABUNO’s.
The XNL LABUNO’s don’t have their own RX and TX LED’s “onboard” to keep the ‘lines as clear as possible’. Therefor we also decided to use the ‘opamp method’ to ensure minimal ‘additional load’ on the (data) lines.
These boards can be used for both the hardware and/or software serial ports of the LABUNO’s
“Multi Pack” NOTE:
The (NON USB) XNL LABUNO download also contains a panelized version of the XNL LABUNO which includes two XNL Logic Monitors, an XNL ESP Direct Board, and an XNL WESP Board which means that it might actually be cheaper to order the panelized version (if your PCB Manufacturer allows pre-panelized boards) if you need or want all modules.
Download Size: 645kb
-
The XNL Mini SIM Adapter is a very simple to assemble product which will make it very easy to interface directly with (mobile) SIM Cards on your breadboard.
Perfect for when you are building a SMS, GPRS, 3G, 4G or other ‘Mobile Telecom’ project on your breadboard with a module which doesn’t have it’s own SIM Card slot.
NOTE:
This project/product has no datasheet/manual in the download! The instructions are listed bellow in the information tabs.
Download Size: 123kb
-
This is our 100x100mm (10x10cm) XNL Protoboard XPB5722-A.
There are two versions, this one which has ‘small ground planes’ between each hole and along it’s edges. and the XPB5722-A1 which doesn’t have these ‘ground planes’
For most users we would recommend using the XPB5722-A1 instead!
Specifications:
Size: 100x100mm
Holes: 1404 (38×36)+36
Spacing: 2.54mm / 0.1”
Model: (38×36)+36P
P/N: XPB5722-A
Download Size: 307kb
-
This is our 100x100mm (10x10cm) XNL Protoboard XPB5722-A.
There are two versions, this one and the XPB5722-A which has ‘small ground planes’ between each hole and along it’s edges.
This is the model/version which we would recommend for most users.
Specifications:
Size: 100x100mm
Holes: 1404 (38×36)+36
Spacing: 2.54mm / 0.1”
Model: (38×36)+36
P/N: XPB5722-A1
Download Size: 88kb
-
Ever “needed” to hook-up some wires to the ‘SIM Card Socket’ of a mobile phone for one of your ‘Sketchy Projects’, but didn’t wanted to solder wires onto the ‘pins’?
Well then maybe this little board might be just what you need for those ‘sketchy SIM Port Projects’ ;)
Download Size: 17kb
-
The XNL STAR-3 is our own ‘answer’ on the commonly known (Chinese) BluePill development board.
The XNL STAR-3 is an (72MHz) ARM® Cortex®-M3 based development board, developed to offer a more ‘developer friendly’ experience than with the commonly used (Chinese) Blue Pill boards.
Quick Overview Specs:
• 72MHz ARM® 32-bit Cortex®-M3
• 64KB or 128KB Flash (program) Memory
• 20KB SRAM
• RTC (With onboard battery)
Download Size: 2.5MB
-
The XNL STAR-3-MB is basically a ‘motherboard’ for the commonly known (Chinese) BluePill development boards.
While at the same time also providing a very easy, fast and convenient way to ‘snap-in-and-flash’ (bootload) your BluePill board without needing additional USB->Serial boards or other flash tools/sticks.
During development the XNL STAR-3-MB also gives you instant access to the USB port of the BluePill itself, an additional USB port which functions as a USB->Serial adapter for TX1 & RX1, an onboard RTC Battery and a (more stable) 3.3V ‘power supply’ for your external 3.3V components and/or modules.
Download: 2.5MB
-
The XNL WESP is our (simple) solution to work with the ESP-12E boards using our XNL LABUNO’s. It basically ‘converts’ your ESP-12E modules into a ‘mini development board’ when used in combination with our LABUNO’s.
This is however not a full (stand-alone) development board, officially put this is ‘just a breakout board’!
NOTE: The download for the XNL WESP also contains the official datasheet of the ESP-12E
“Multi Pack” NOTE:
The (NON USB) XNL LABUNO download also contains a panelized version of the XNL LABUNO which includes two XNL Logic Monitors, an XNL ESP Direct Board, and an XNL WESP Board which means that it might actually be cheaper to order the panelized version (if your PCB Manufacturer allows pre-panelized boards) if you need or want all modules.
