-
EoL
This small board is what I/we’ve used for a long time when we needed to boot-load our newly arrived Atmega328’s, often we used this board together with the XNL ISP Speed Flash Board to flash and/or boot-load all kinds of different AVR’s for our projects.
These days we however don’t use (or support) it anymore, simply because the XNL LABUNO Overkill Edition has an ISP Programmer build-in, which also has it’s own onboard USB controller, which means we don’t have to connect it to an USB to Serial adapter first (like the XNL F.U.T.S.).
NOTE: The larger (red) board shown in the photo’s is the XNL ISP Speed Flash Board which is not included in this download!
Download Size: 1.75mb
-
A simple add-on for the XNL LABUNO Overkill Edition which enables you to quickly and easily flash and/or boot-load a wide range of AVR microcontrollers by simply using your XNL LABUNO Overkill Edition’s AVR/ISP Programmer header
Microcontrollers supported by this board
– ATmega 48, 88, 168 & 328 (28 pin)
– ATmega 644 & 1284 (40 Pin)
– Tiny 2313 (20 Pin)
– Tiny 44 & 84 (14 pin)
– Tiny 45 & 85 (8 pin)
Download Size: 1.6mb
-
The XNL LABUNO is ‘our answer’ to the Arduino® Uno, but with (much) more control over your hardware.
Some of the features you have full control over with the LABUNO are:
– Pull-up resistors on the ‘reset-line’
– Enable/Disable RTS Reset
– Switch TTL communication between HW / SW
– VCC source selection
– High power LM3940 3.3V Regulator
– Full control over the serial pins
– Build-in support for ESP board (and communication)
Next to these (and more) features, the headers (next to the microcontroller) also ‘line-up’ 1:1 with the microcontroller pin-out.
NOTE:
This model requires an USB->TTL adapter like for example the XNL F.U.T.S. or an FTDI cable to communicate with your computer. The LABUNO USB has an onboard USB-Serial chip and thus does not need an additional USB adapter/cable. We also have the LABUNO Overkill Edition which has even more ‘on-board’ features and also has an onboard USB controller.
“Multi Pack” NOTE:
This download also contains a panelized version of the XNL LABUNO which includes two XNL Logic Monitors, an XNL ESP Direct Board, and an XNL WESP Board which means that it might actually be cheaper to order the panelized version (if your PCB Manufacturer allows pre-panelized boards) if you need or want all modules.
Download Size: 4mb
-
The XNL LABUNO Overkill Edition is an ‘expanded version’ of our XNL LABUNO USB.
Some of the features you have full control over with the LABUNO are:
– Pull-up resistors on the ‘reset-line’
– Enable/Disable RTS Reset
– Switch TTL communication between HW / SW
– VCC source selection
– High power LM3940 3.3V Regulator
– Full control over the serial pins
– Build-in support for ESP board (and communication)
Additional Features with the LABUNO Overkill Edition:
– Full access to ALL serial/UART pins
– Three onboard Ready to use Servo Ports
– I2C/OLED LCD Header Ready to use
– Onboard AVR/ISP Programmer using the
Arduino as ISP sketch.
Next to these (and more) features, the headers (next to the microcontroller) also ‘line-up’ 1:1 with the microcontroller pin-out.
NOTE:
This has it’s own ‘onboard’ USB to serial (TTL) chip (the CH340G), while the LABUNO does not have any USB controller/chip onboard. So if you prefer to choose your own USB->Serial chip, we would like you to recommend to check out the LABUNO instead. We also have the XNL LABUNO USB which is a bit more ‘subtle’ so to speak.
“Multi Pack” NOTE:
The (NON USB) XNL LABUNO download also contains a panelized version of the XNL LABUNO which includes two XNL Logic Monitors, an XNL ESP Direct Board, and an XNL WESP Board which means that it might actually be cheaper to order the panelized version (if your PCB Manufacturer allows pre-panelized boards) if you need or want all modules.
Download Size: 4.5mb
-
The XNL LABUNO USB is ‘our answer’ to the Arduino® Uno, but with (much) more control over your hardware.
Some of the features you have full control over with the LABUNO are:
– Pull-up resistors on the ‘reset-line’
– Enable/Disable RTS Reset
– Switch TTL communication between HW / SW
– VCC source selection
– High power LM3940 3.3V Regulator
– Full control over the serial pins
– Build-in support for ESP board (and communication)
Next to these (and more) features, the headers (next to the microcontroller) also ‘line-up’ 1:1 with the microcontroller pin-out.
NOTE:
This has it’s own ‘onboard’ USB to serial (TTL) chip (the CH340G), while the LABUNO does not have any USB controller/chip onboard. So if you prefer to choose your own USB->Serial chip, we would like you to recommend to check out the LABUNO instead. We also have the LABUNO Overkill Edition which has even more ‘on-board’ features and also has an onboard USB controller.
“Multi Pack” NOTE:
The (NON USB) XNL LABUNO download also contains a panelized version of the XNL LABUNO which includes two XNL Logic Monitors, an XNL ESP Direct Board, and an XNL WESP Board which means that it might actually be cheaper to order the panelized version (if your PCB Manufacturer allows pre-panelized boards) if you need or want all modules.
Download Size: 3.8mb
-
The XNL STAR-3 is our own ‘answer’ on the commonly known (Chinese) BluePill development board.
The XNL STAR-3 is an (72MHz) ARM® Cortex®-M3 based development board, developed to offer a more ‘developer friendly’ experience than with the commonly used (Chinese) Blue Pill boards.
Quick Overview Specs:
• 72MHz ARM® 32-bit Cortex®-M3
• 64KB or 128KB Flash (program) Memory
• 20KB SRAM
• RTC (With onboard battery)
Download Size: 2.5MB
-
The XNL STAR-3-MB is basically a ‘motherboard’ for the commonly known (Chinese) BluePill development boards.
While at the same time also providing a very easy, fast and convenient way to ‘snap-in-and-flash’ (bootload) your BluePill board without needing additional USB->Serial boards or other flash tools/sticks.
During development the XNL STAR-3-MB also gives you instant access to the USB port of the BluePill itself, an additional USB port which functions as a USB->Serial adapter for TX1 & RX1, an onboard RTC Battery and a (more stable) 3.3V ‘power supply’ for your external 3.3V components and/or modules.
Download: 2.5MB
-
The XNL WESP is our (simple) solution to work with the ESP-12E boards using our XNL LABUNO’s. It basically ‘converts’ your ESP-12E modules into a ‘mini development board’ when used in combination with our LABUNO’s.
This is however not a full (stand-alone) development board, officially put this is ‘just a breakout board’!
NOTE: The download for the XNL WESP also contains the official datasheet of the ESP-12E
“Multi Pack” NOTE:
The (NON USB) XNL LABUNO download also contains a panelized version of the XNL LABUNO which includes two XNL Logic Monitors, an XNL ESP Direct Board, and an XNL WESP Board which means that it might actually be cheaper to order the panelized version (if your PCB Manufacturer allows pre-panelized boards) if you need or want all modules.
